manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 239 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 239

•

Service Park Assist System (with a single chime)

•

Oil Change Required (with a single chime)

•

ECO (Fuel Saver Indicator) — if equipped

Oil Change Required

Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10 sec-
onds after a single chime has sounded to indicate the next
scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.

Unless reset, this message will continue to display each
time you turn the ignition switch to the ON position. To
turn off the message temporarily, press and release the
FUNCTION SELECT button. To reset the oil change

indicator system (after performing the scheduled main-
tenance) perform the following procedure:

1. Turn the ignition switch to the ON position.

Do not

start the engine

.

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the LOCK position.

NOTE:

If the indicator message illuminates when you

start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.

Trip Functions

Press and until one of the following Trip Functions
displays in the EVIC:

•

Average Fuel Economy

•

Distance To Empty

4

UNDERSTANDING YOUR INSTRUMENT PANEL

237

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments