Jeep Liberty 2011 Page 407 Owner'S Manual Download | Manualshive

Page: 407 / 540

background image

WARNING! (Continued)

•

Safety chains must always be used between your
vehicle and trailer. Always connect the chains to
the frame or hook retainers of the vehicle hitch.
Cross the chains under the trailer tongue and
allow enough slack for turning corners.

•

Vehicles with trailers should not be parked on a
grade. When parking, apply the parking brake on
the tow vehicle. Put the tow vehicle transmission
in PARK. Always, block or

ⴖ

chock

ⴖ

the trailer

wheels.

•

GCWR must not be exceeded.

•

Total weight must be distributed between the tow
vehicle and the trailer such that the following four
ratings are not exceeded:
1. GVWR
2. GTW

(Continued)

WARNING! (Continued)

3. GAWR
4. Tongue weight rating for the trailer hitch utilized
(This requirement may limit the ability to always
achieve the 10% to 15% range of tongue weight as a
percentage of total trailer weight).

Towing Requirements – Tires

− Do not attempt to tow a trailer while using a compact

spare tire.

− Proper tire inflation pressures are essential to the safe

and satisfactory operation of your vehicle. Refer to
“Tires – General Information” in “Starting and Oper-
ating” for information on tire pressures and for proper
tire inflation procedures.

− Check the trailer tires for proper tire inflation pres-

sures before trailer usage.

5

STARTING AND OPERATING

405

«
...
405
406
407
408
409
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

Brand: Acdeos Pages: 38

Brand: Hama Pages: 6

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

Brand: EUFAB Pages: 12

2008 MX-5 Miata

Brand: Mazda Pages: 400

Brand: Kargo Master Pages: 6

DBALL2-HYUNDAI9

Brand: Xpresskit Pages: 13

2011 3500 Chassis Cab

Brand: RAM Pages: 92

Brand: P-Invent Pages: 4

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: Hyundai Pages: 18

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Brand: UAZ Pages: 112

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Camoplast Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands