Home
/
Jeep
/
Liberty 2011
/
Owner'S Manual

Jeep Liberty 2011, Owner'S Manual, Page: 206 / 540

Share

Page: 206 / 540

Jeep Liberty 2011 Owner'S Manual Download Page 206

1. Flip the spring-loaded latch pull-loops up.

2. Pull the loops upward and twist them one-quarter
turn so that they are parallel to the slots in the storage bin
cover.

3. Lift the cover upward over the loops.

4. Turn over the cover and reinstall it.

NOTE:

You can install the cover with either side facing

upward.

5. With the cover seated in the floor, pull upward on
loops and twist them one-quarter turn so that they are no
longer parallel to the slots in the cover.

6. Flip the loops down.

WARNING!

A loose storage bin cover thrown forward in a acci-
dent or hard stop could endanger the occupants of
the vehicle. Always latch the storage bin cover to the
cargo load floor with the spring-loaded latches when
not accessing the storage bin.

Cargo Load Floor Loops

204

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
204
205
206
207
208
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments