Home
/
Jeep
/
Liberty 2011
/
Owner'S Manual

Jeep Liberty 2011, Owner'S Manual, Page: 188 / 540

Share

Page: 188 / 540

Jeep Liberty 2011 Owner'S Manual Download Page 188

This can usually be found where the hanging antenna
wire is attached to the garage door opener motor (it is
NOT the button normally used to open and close the
door).

1. Firmly press and release the LEARN or TRAINING
button. The name and color of the button may vary by
manufacturer.

NOTE:

You have 30 seconds in which to initiate the next

step after the LEARN button has been pressed.

2. Return to the vehicle and press the programmed
HomeLink

威

button twice (holding the button for two

seconds each time). If the device is plugged in and
activates, programming is complete.

If the device does not activate, press the button a third
time (for two seconds) to complete the training.

If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.

To program the remaining two HomeLink

威

buttons,

repeat each step for each remaining button. DO NOT
erase the channels.

1 — Garage Door Opener
2 — Training Button

186

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
186
187
188
189
190
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments