manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 303 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 303

The operator can override the AUTO mode setting to
change airflow distribution by rotating the Mode Control
knob (on the right) to one of the following positions.

•

Panel

Air is directed through the outlets in the instrument
panel. These outlets can be adjusted to direct airflow.

NOTE:

The center instrument panel outlets can be

aimed so that they are directed toward the rear seat
passengers for maximum airflow to the rear.

•

Bi-Level

Air is directed through the panel and floor outlets.

NOTE:

For all settings except full cold or full hot, there

is a difference in temperature between the upper and
lower outlets. The warmer air flows to the floor outlets.
This feature gives improved comfort during sunny but
cool conditions.

•

Floor

Air is directed through the floor outlets with a
small amount flowing through the defrost and side

window demist outlets.

•

Mix

Air is directed through the floor, defrost, and side
window demist outlets. This setting works best in
cold or snowy conditions that require extra heat to

the windshield. This setting is good for maintaining
comfort while reducing moisture on the windshield.

•

Defrost

Air is directed through the windshield and side
window demist outlets. Use this mode with maxi-

mum blower and temperature settings for best wind-
shield and side window defrosting.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

301

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments