Home
/
Jeep
/
Liberty 2011
/
Owner'S Manual

Jeep Liberty 2011, Owner'S Manual, Page: 101 / 540

Share

Page: 101 / 540

Jeep Liberty 2011 Owner'S Manual Download Page 101

Automatic Dimming Mirror — If Equipped

This mirror automatically adjusts for headlight glare
from vehicles behind you. You can turn the feature on or
off by pressing the button at the base of the mirror. A light
to the left of the button will illuminate to indicate when
the dimming feature is activated. The sensor to the right
of the button does not illuminate.

CAUTION!

To avoid damage to the mirror during cleaning, never
spray any cleaning solution directly onto the mirror.
Apply the solution onto a clean cloth and wipe the
mirror clean.

Outside Mirrors

To receive maximum benefit, adjust the outside mirror(s)
to center on the adjacent lane of traffic and a slight
overlap of the view obtained from the inside mirror.

NOTE:

The passenger side convex outside mirror will

give a much wider view to the rear, and especially of the
lane next to your vehicle.

Automatic Dimming Mirror

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

99

«
...
99
100
101
102
103
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments