Jeep Liberty 2011 Page 197 Owner'S Manual Download | Manualshive

Page: 197 / 540

background image

Sky Slider™ Control

The Sky Slider™ switch is located between the sun visors
on the overhead console.

NOTE:

The Sky Slider™ switch will operate when the

ignition switch is turned to the ON or ACC position.

Opening The Sky Slider™

Using Automatic Mode

Press the switch rearward and release it within one-half
second and the Sky Slider™ will open from the front and
move automatically toward the rear of the vehicle.

Press the switch forward and release it within one-half
second and the Sky Slider™ will open from the rear and
move automatically toward the front of the vehicle.

NOTE:

•

During operation, any movement of the Sky Slider™
switch will stop the Sky Slider™ roof.

•

To resume the operation from a partially open posi-
tion, press and release the switch a second time.

•

The Sky Slider™ will not open from the front and the
rear at the same time. The Sky Slider™ must close fully
before opening it from the opposite end.

Sky Slider™ Switch

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

195

«
...
195
196
197
198
199
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

Brand: LaserTrack Pages: 12

Electronic Parking Disc II

Brand: Jacob Jensen Pages: 28

Brand: Cequent Pages: 9

Brand: Motoalliance Pages: 8

Brand: Cadillac Pages: 409

Brand: Fortin Pages: 9

Brand: Improved Racing Pages: 17

Brand: Vangear Pages: 5

Brand: Safe Fleet Pages: 20

Brand: Subaru Pages: 540

MagicSpeed MS900

Brand: Waeco Pages: 120

Security Cage Kit

Brand: Toro Pages: 8

Brand: V8 equipment Pages: 34

FABIA II TMB PS 035

Brand: Skoda Pages: 16

Brand: Summit Racing Pages: 11

Brand: Menabo Pages: 8

Brand: Lexus Pages: 6

Brand: Volkswagen Zubehör Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands