Jeep Liberty 2011 Page 170 Owner'S Manual Download | Manualshive

Page: 170 / 540

background image

The sensitivity of the system is adjustable from the
windshield wiper/washer control lever. Wiper delay
position 1 is the least sensitive and wiper delay position
5 is the most sensitive. Choose position 3 for normal rain
conditions. Choose position 2 or 1 if you desire less wiper
sensitivity. Choose position 4 or 5 if you desire more
sensitivity. Place the lever in the off position when not
using the system.

NOTE:

•

The rain-sensing feature will not operate when the
wiper speed is in the low or high position.

•

The rain-sensing feature may not function properly
when ice or dried salt water is present on the wind-
shield.

•

Use of Rain-X

威

or products containing wax or silicone

may reduce rain sensor performance.

•

The rain-sensing feature can be turned on and off
through the Electronic Vehicle Information Center
(EVIC) — if equipped. Refer to “Electronic Vehicle
Information

Center

(EVIC)/Personal

Settings

(Customer-Programmable Features)” in “Understand-
ing Your Instrument Panel” for further information.

The rain-sensing system has protective features for the
wiper blades and arms. It will not operate under the
following conditions:

•

Low Temperature Wipe Inhibit

— The rain-sensing

feature will not operate when the ignition is first
switched ON, the vehicle is stationary, and the outside
temperature is below 32° F (0° C). If the wiper control
is moved, the vehicle speed becomes greater than
0 mph (0 km/h), or the outside temperature rises
above freezing the rain-sensing feature will then op-
erate.

168

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
168
169
170
171
172
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Brand: PAC Pages: 4

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: Jeep Pages: 1528

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Brand: Quadratec Pages: 12

Brand: cam Pages: 6

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Kia Pages: 58

Brand: Ford Pages: 585

Brand: Bilstein Pages: 7

Brand: Kia Pages: 233

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands