manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 385 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 385

Should this occur, you should stop as soon as possible
and inflate the tires with low pressure (those flashing in
the EVIC graphic) to the vehicle’s recommended cold
placard pressure value. Once the system receives the
updated tire pressures, the system will automatically
update, the graphic display in the EVIC will stop flash-
ing, and the “Tire Pressure Monitoring Telltale Light”

will turn off. The vehicle may need to be driven for up to
20 minutes above 15 mph (24 km/h) in order for the
TPMS to receive this information.

Check TPMS Warning

When a system fault is detected, the “Tire Pressure
Monitoring Telltale Light” will flash on and off for
75 seconds and then remain on solid. The system fault
will also sound a chime. In addition, the EVIC will
display a

⬙

CHECK TPM SYSTEM

⬙

message for three

seconds and then display dashes (- -) in place of the
pressure value to indicate which sensor is not being
received.

5

STARTING AND OPERATING

383

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments