manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 330 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 330

Shift Positions

The transfer case switch is located on the center console
next to the shift lever.

2WD

Rear Wheel Drive High Range - This range is for normal
street and highway driving on dry hard-surfaced roads.

4WD Auto

Four-Wheel Drive Auto High Range – This active on-
demand range makes available optimum traction for a
wide range of conditions, while maximizing driver con-
venience. This position is always in four-wheel drive
mode, with a normal 42% front axle, 58% rear axle torque
split. The system also anticipates and prevents slip by
redirecting torque as necessary, up to 100% to the front or
rear axle, if needed.

4WD Low

Four-Wheel Drive Low Range - This range is for low
speed four-wheel drive. Locks the front driveshaft and
rear driveshaft together forcing the front and rear wheels
to rotate at the same speed. Additional traction and
maximum pulling power for loose or slippery road
surfaces only. Do not exceed 25 mph (40 km/h).

Transfer Case Switch

328

STARTING AND OPERATING

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments