manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 387 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 387

turn on upon the next ignition key cycle. In addition, the
EVIC will display a Low Pressure message and a graphic
showing the low tire pressure value flashing.

3. After driving the vehicle for up to 20 minutes above
15 mph (24 km/h) the “TPMS Telltale Light” will turn
OFF, as long as no tire pressure is below the low-pressure
warning limit in any of the four active road tires.

4. The EVIC will display a graphic showing the tire
pressure value in place of the flashing low tire pressure
value. The EVIC will also display a “SPARE LOW
PRESSURE” message to remind you to service the flat
tire.

Vehicles with Compact Spare

1. The compact spare tire does not have a tire pressure
monitoring sensor. Therefore, the TPMS will not monitor
the pressure in the compact spare tire.

2. If you install the compact spare tire in place of a road
tire that has a pressure below the low-pressure warning
limit, upon the next ignition key cycle, the “TPMS Telltale
Light” will remain on and a chime will sound. In
addition, the graphic in the EVIC will still display a
flashing pressure value.

3. After driving the vehicle for up to 20 minutes above
15 mph (24 km/h), the “TPMS Telltale Light” will flash
on and off for 75 seconds and then remain on solid. In
addition, the EVIC will display a

⬙

CHECK TPM SYS-

TEM

⬙

message for three seconds and then display dashes

(- -) in place of the pressure value.

4. For each subsequent ignition key cycle, a chime will
sound, the “TPMS Telltale Light” will flash on and off for
75 seconds and then remain on solid, and the EVIC will
display a

⬙

CHECK TPM SYSTEM

⬙

message for three

seconds and then display dashes (- -) in place of the
pressure value.

5

STARTING AND OPERATING

385

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments