Jeep Liberty 2011 Page 86 Owner'S Manual Download | Manualshive

Page: 86 / 540

background image

downward into the seat, removing slack in the straps
according to the child restraint manufacturer’s instruc-
tions.

WARNING!

Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be badly injured or
killed. Follow the manufacturer’s directions exactly
when installing an infant or child restraint.

Installing Child Restraints Using The Vehicle Seat
Belt

The passenger seat belts are equipped with either cinch-
ing latch plates or automatic locking retractors, which are
designed to keep the lap portion tight around the child
restraint so that it is not necessary to use a locking clip. If
the seat belt has a cinching latch plate, pulling up on the
shoulder portion of the lap/shoulder belt will tighten the

belt. However, any seat belt system may loosen with
time, so check the belt occasionally, and pull it tight if
necessary.

If the seat belt has an automatic locking retractor, pull the
belt from the retractor until there is enough slack to allow
you to pass the belt through the child restraint and slide
the latch plate into the buckle. Then, pull the belt until it
is all extracted from the retractor. Allow the belt to return
to the retractor, pulling on the excess webbing to tighten
the lap portion around the child restraint. Refer to
“Automatic Locking Mode”.

In the rear seat, you may have trouble tightening the
lap/shoulder belt on the child restraint because the
buckle or latch plate is too close to the belt path opening
on the restraint. Disconnect the latch plate from the
buckle and twist the short buckle-end belt several times
to shorten it. Insert the latch plate into the buckle with the
RELEASE button facing out.

84

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
84
85
86
87
88
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

AUDI 4G HIGHEND

Brand: KAP Pages: 20

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Transit Vancouver Wagon

Brand: Webasto Pages: 44

Brand: WABCO Pages: 48

Brand: Würth Pages: 36

Brand: Whelen Engineering Company Pages: 9

Brand: Audi Pages: 63

Brand: Oldsmobile Pages: 358

Brand: Toyota Pages: 36

Brand: LaserLine Pages: 4

Brand: BabySafe Pages: 43

Brand: E-Lead Pages: 11

ASENTO EV-EXP18R

Brand: ADAPT SOLUTIONS Pages: 25

Brand: Air Lift Pages: 24

Brand: Discount Car Stereo Pages: 5

Brand: PROUSER Pages: 40

Brand: Malone Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands