manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 194 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 194

windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occur-
rence and can be minimized. If the buffeting occurs with
the rear windows open, then open the front and rear
windows together to minimize the buffeting. If the
buffeting occurs with the sunroof open, adjust the sun-
roof opening to minimize the buffeting or open any
window.

Sunroof Maintenance

Use only a non-abrasive cleaner and a soft cloth to clean
the glass panel.

Ignition Off Operation

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power sunroof switch
will remain active for 45 seconds after the ignition switch
is turned to the LOCK position. Opening either front
door will cancel this feature.

For vehicles equipped with the EVIC, the power sunroof
switch will remain active for up to approximately ten
minutes after the ignition switch is turned to the LOCK
position. Opening either front door will cancel this
feature. The time is programmable. Refer to “Electronic
Vehicle Information Center (EVIC)/Personal Settings
(Customer-Programmable Features)” in “Understanding
Your Instrument Panel” for further information.

SKY SLIDER™ FULL LENGTH OPEN ROOF — IF
EQUIPPED

The Sky Slider™ is a full-length, soft-top, power roof that
opens front to rear or rear to front.

Sky Slider™ Usage Precautions

NOTE:

•

The system will not operate when ambient tempera-
ture is at –4°F (–20°C) or lower.

192

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments