Jeep Liberty 2011 Page 424 Owner'S Manual Download | Manualshive

Page: 424 / 540

background image

WARNING! (Continued)

•

Being under a jacked-up vehicle is dangerous. The
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
under a vehicle that is on a jack.

•

Never start or run the engine while the vehicle is
on a jack. If you need to get under a raised vehicle,
take it to a service center where it can be raised on
a lift.

•

The jack is designed to be used as a tool for
changing tires only. The jack should not be used to
lift the vehicle for service purposes. The vehicle
should be jacked on a firm level surface only.
Avoid ice or slippery areas.

Jack Location

The scissor-type jack and tire changing tools are located
in the cargo compartment behind a trim cover on the left
rear trim panel. The latch is located at the bottom of the
trim cover.

Jack Storage Location

422

WHAT TO DO IN EMERGENCIES

«
...
422
423
424
425
426
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

Brand: RaceChip Pages: 12

Brand: Mitsubishi Pages: 160

Brand: Cadillac Pages: 442

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Brand: PEUGEOT Pages: 249

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

Brand: Saab Pages: 15

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

Brand: Mobridge Pages: 20

Brand: Hama Pages: 13

Brand: Arrista Pages: 2

Brand: Lexus Pages: 878

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

Brand: PERODUA Pages: 43

WG Grand Cherokee 2002

Brand: Jeep Pages: 74

Brand: FAAFTECH Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands