Jeep Liberty 2011 Page 454 Owner'S Manual Download | Manualshive

Page: 454 / 540

background image

WARNING!

•

Use only refrigerants and compressor lubricants
approved by the manufacturer for your air condi-
tioning system. Some unapproved refrigerants are
flammable and can explode, injuring you. Other
unapproved refrigerants or lubricants can cause
the system to fail, requiring costly repairs. Refer to
Warranty Information Book, located on the DVD,
for further warranty information.

•

The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected
should be done by an experienced technician.

Refrigerant Recovery and Recycling

R-134a air conditioning refrigerant is a hydrofluoro-
carbon (HFC) that is endorsed by the Environmental
Protection Agency and is an ozone-saving product. How-
ever, the manufacturer recommends that air conditioning
service be performed by an authorized dealer or other
service facilities using recovery and recycling equipment.

NOTE:

Use only manufacturer approved A/C System

Sealers, Stop Leak Products, Seal Conditioners, Compres-
sor Oil, and Refrigerants.

A/C Air Filter – If Equipped

Refer to the “Maintenance Schedule” for the proper
maintenance intervals.

WARNING!

Do not remove the A/C Air Filter while the blower is
operating or personal injury may result.

452

MAINTAINING YOUR VEHICLE

«
...
452
453
454
455
456
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

Brand: Ranger design Pages: 6

Brand: Camcar Pages: 6

Brand: Abarth Pages: 176

Brand: SnapPad Pages: 5

Brand: Sirius Satellite Radio Pages: 8

Brand: JKS Pages: 6

Brand: Saab Pages: 15

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

Brand: Skoda Pages: 2

Brand: Prime Design Pages: 8

Brand: Phonocar Pages: 28

Brand: Rydeen Pages: 14

Brand: Lexus Pages: 878

Brand: Car-Interface Pages: 25

Brand: Lincoln Pages: 364

Brand: chinavasion Pages: 3

Brand: Weather Guard Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands