Jeep Liberty 2011 Page 516 Owner'S Manual Download | Manualshive

Page: 516 / 540

background image

Temperature Grades

The temperature grades are A (the highest), B, and C,
representing the tire’s resistance to the generation of heat
and its ability to dissipate heat, when tested under
controlled conditions on a specified indoor laboratory
test wheel. Sustained high temperature can cause the
material of the tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance, which all
passenger car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades B and A repre-
sent higher levels of performance on the laboratory test
wheel, than the minimum required by law.

WARNING!

The temperature grade for this tire is established for
a tire that is properly inflated and not overloaded.
Excessive speed, under-inflation, or excessive load-
ing, either separately or in combination, can cause
heat buildup and possible tire failure.

514

IF YOU NEED CONSUMER ASSISTANCE

«
...
514
515
516
517
518
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

Brand: Warrior Products Pages: 2

Brand: Wallbox Pages: 7

Brand: IAG Pages: 3

Brand: Prorack Pages: 14

Brand: DriveRight Pages: 16

Brand: Pontiac Pages: 20

Brand: AL-KO Pages: 40

2007 SLR Mclaren

Brand: Mercedes-Benz Pages: 425

IT FITS RBO1018

Brand: RBO Pages: 36

Jumpy Miltispace

Brand: CITROËN Pages: 164

Brand: Directed Pages: 30

Brand: Fabbri Pages: 32

Brand: Whelen Engineering Company Pages: 2

Brand: TracRac Pages: 8

Brand: Nav TV Pages: 8

Brand: Haltech Pages: 13

Brand: AA Products Pages: 8

Brand: Discount Car Stereo Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands