manualshive.com logo in svg

IDT 89HPEB383, User Manual

Share
Download
IDT 89HPEB383 User Manual Download Page 45

4. Addressing > Prefetchable Space

31

PEB383 User Manual

July 25, 2011

Integrated Device Technology, Inc.

Confidential - NDA Required

The memory-mapped I/O address range that is defined by the Base and Limit registers are always 
aligned to a 1-MB boundary and has a size granularity of 1 MB. 

4.3

Prefetchable Space

The prefetchable address space maps memory address ranges of devices that are prefetchable; that is, 
devices that do not have side-effects during reads. For PCI-to-PCIe reads, prefetching occurs in this 
space for all memory read commands (MemRd, MemRdLine, MemRdMult) issued on the PCI bus. For 
these Read commands, the PEB383 prefetches data according to prefetching algorithm defined in 

“Prefetching Algorithm”

. For PCIe-to-PCI reads, the number of bytes to be read is determined by the 

Memory Read Request. 

The Prefetchable Memory Base, Prefetchable Memory Limit, Prefetchable Base Upper 32 Bits, and 
Prefetchable Limit Upper 32 Bits registers in the bridge configuration header specify an address range 
that is used by the bridge to determine whether to forward PCIe and PCI memory read and memory 
write transactions across the bridge. The prefetchable memory address range defined by these registers 
is always aligned to a 1-MB boundary and has a size granularity of 1 MB. If the address specified by 
the Prefetchable Memory Base and Prefetchable Base Upper 32 Bits registers is set to a value higher 
than the address specified by the Prefetchable Memory Limit and Prefetchable Limit Upper 32 Bits 
registers, the address range is disabled. 

Following register bits effect the response by the bridge to memory transactions:

•

Memory Enable bit in 

“PCI Control and Status Register”

•

Bus Master Enable bit in 

“PCI Control and Status Register”

•

VGA Enable bit in 

“PCI Bridge Control and Interrupt Register”

The PEB383 forwards memory transactions downstream from its PCIe Interface to its PCI Interface if 
a memory address is in the range defined by the Prefetchable Memory Base and Prefetchable Memory 
Limit registers. Conversely, a memory transaction on the PCI Interface that is within this address range 
is not be forwarded upstream to the PCIe Interface. Any memory transactions on the PCI Interface that 
are outside this address range are forwarded upstream to the PCIe Interface (provided they are not in 
the address range defined by the memory-mapped I/O address range registers). 

If the Prefetchable Memory Base is programmed to have a value greater than the Prefetchable Memory 
Limit, then the prefetchable memory range is disabled. In this case, all memory transaction forwarding 
is determined by the memory-mapped I/O base and limit registers. Note that all four prefetchable base 
and limit registers must be considered when disabling the prefetchable range.

Unlike non-prefetchable memory-mapped I/O memory, Prefetchable memory can be located below, 
above, or span across the first 4-GB address boundary. 

Figure 10

 illustrates a prefetchable memory 

window that spans across the 4-GB address boundary. Memory locations above 4 GB are accessed 
using 64-bit addressing. PCIe memory transactions that use the Short Address (32-bit) format can 
target a non-prefetchable memory window or the portion of a prefetchable memory window that is 
below the first 4-GB address boundary. Memory transactions that use the Long Address (64-bit) format 
can target the portion of a prefetchable memory window that is at or above the first 4-GB address 
boundary.

Summary of Contents for 89HPEB383









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands