IDT 89HPEB383 User Manual Download Page 32

Page: 32 / 264

2. Signal Descriptions > EEPROM Interface Signals

PEB383 User Manual

July 25, 2011

Integrated Device Technology, Inc.

Confidential - NDA Required

2.4

EEPROM Interface Signals

PCI_RSTn

PCI Out

PCI reset: This signal resets all devices
on the PC bus.

No pull-up or pull-down resistor is
required.

PCI_SERRn

PCI Bidir OD

System Error. This signal indicates an
address or attribute phase parity error
occurred.

Pull-up (8.2K) to VIO_PCI.

PCI_STOPn

PCI Bidir

Stop. A bus target asserts this signal to
indicate it wants to stop the current
transaction on the current data phase.

Pull-up (8.2K) to VIO_PCI.

PCI_TRDYn

PCI Bidir

Target Ready. The bus target asserts
this signal to indicate it is ready to
complete the current data phase.

Pull-up (8.2K) to VIO_PCI.

Table 4: EEPROM Interface Signals

Name

Pin Type

Description

Design Recommendation

SR_CLK

3.3 Out

Serial ROM clock: This signal is derived
from REFCLKn/p (see

“System

Diagram”

No pull-up or pull-down resistor is
required.

SR_CSn

3.3 Out

Serial ROM chip select: This active-low
signal activates the chip-select (CS) on
the external EEPROM.

SR_DIN

3.3 Out

Serial ROM data in: This signal
transfers output data from the PEB383
to the EEPROM.

SR_DOUT

3.3 In PU

Serial ROM data out: This signal
transfers input data from the EEPROM
to the PEB383.

Table 3: PCI Interface Signals

(Continued)

Name

Pin Type

Description

Design Recommendation

Summary of Contents for 89HPEB383









































































































































































































































































Search results

Summary of Contents for 89HPEB383

Reviews:

Related manuals for 89HPEB383

Brands by name

Popular brands

IDT 89HPEB383, User Manual

Search results

Summary of Contents for 89HPEB383

Reviews:

Related manuals for 89HPEB383

Brands by name

Popular brands