manualshive.com logo in svg

IDT 89HPEB383, User Manual

Share
Download
IDT 89HPEB383 User Manual Download Page 155

14. Register Descriptions > Register Map

141

PEB383 User Manual

July 25, 2011

Integrated Device Technology, Inc.

Confidential - NDA Required

21

MA_ERR

Master-Abort Mode

This bit controls the behavior of a bridge when it receives a 
Master-Abort termination (for example, an Unsupported 
Request on PCIe) on either interface. 

0 = Do not report Master-Aborts. When a UR response is 

received from PCIe for non-posted transactions, and 
when the secondary side is operating in PCI mode, 
return 0xFFFF_FFFF on reads and complete I/O writes 
normally. When a Master-Abort is received on the PCI 
Interface for posted transactions initiated from the PCIe 
Interface, no action is taken (that is, all data is 
discarded).

1 = Report UR Completions from PCIe by signaling 

Target-Abort on the PCI Interface when the PCI Interface 
is operating in PCI mode. For posted transactions 
initiated from the PCIe Interface and Master-Aborted on 
the PCI Interface, the bridge must return an 
ERR_NONFATAL (by default) or ERR_FATAL 
transaction (provided the SERR# Enable bit is set in the 
Command register). The severity is selectable only if 
Advanced Error Reporting is supported.

R/W

0

20

VGA_16BIT_EN

VGA 16-Bit Enable

This bit enables the bridge to provide 16-bit decoding of 
VGA I/O address precluding the decoding of alias addresses 
every 1 KB. This bit has meaning only if VGA Enable bit is 
set. 

1 = Executes 16-bit address decodes on VGA I/O accesses

0 = Executes 10-bit address decodes on VGA I/O accesses

R/W

0

 (Continued)

Bits

Name

Description

Type

Reset value

Summary of Contents for 89HPEB383









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands