manualshive.com logo in svg

ICRealtime Edge IPEG-D20F-IRW3, User Manual

The ICRealtime Edge IPEG-D20F-IRW3 is a cutting-edge surveillance camera equipped with advanced infrared technology. Capture high-quality footage day or night with this durable and efficient device. Enhance your security setup by utilizing its intelligent features. For complete control and understanding of this product's capabilities, you can easily download the user manual for free from manualshive.com.

Share
Download
background image

IP Address

When you select

Static

in

Mode

, enter the IP address and subnet

mask as necessary.

Subnet Mask

Parameter

Description

Default Gateway

●

IPv6 does not have subnet mask.

●

The default gateway must be in the same network segment
with the IP address.

Preferred DNS

IP address of the preferred DNS.

Alternate DNS

IP address of the alternate DNS.

Enable ARP/Ping to
set IP address
service

Select the checkbox and acquire the camera MAC address. You
can then modify and configure the device IP address with
ARP/ping command.
This is enabled by default. If this is not enabled, the IP address
cannot be configured with a ping packet.

A demonstration of configuring IP address with ARP/Ping.

1. Have the camera and a PC within the same local network,

and then acquire a usable IP address.

2. Get the MAC address of the camera from the device label.
3. Open command editor on the PC and enter the

following command.

4. Restart the camera.
5. Check the PC command line, if information such as

Reply

from 192.168.0.125

…

is displayed, the configuration is

successful.

6. Enter http://(IP address) in the browser address bar to log

in.

78

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Reviews:

No comments

Related manuals for Edge IPEG-D20F-IRW3

Panasonic Lumix H-FSA14140 Owner'S Manual preview
Lumix H-FSA14140
Brand: Panasonic Pages: 26
Panasonic Lumix H-HS12035 Owner'S Manual preview
Lumix H-HS12035
Brand: Panasonic Pages: 26
Panasonic HFS1442A Owner'S Manual preview
HFS1442A
Brand: Panasonic Pages: 26
Panasonic H-NS043 Owner'S Manual preview
H-NS043
Brand: Panasonic Pages: 26
Panasonic H-H025 Operating Instructions preview
H-H025
Brand: Panasonic Pages: 2
Panasonic H-FS35100 Operating Instructions preview
H-FS35100
Brand: Panasonic Pages: 2
Panasonic H-FS045200 - Lumix Telephoto Zoom Lens Operating Instructions Manual preview
H-FS045200 - Lumix Telephoto Zoom Lens
Brand: Panasonic Pages: 26
Panasonic ET-D3LEW10 Operating Instruction preview
ET-D3LEW10
Brand: Panasonic Pages: 18
Panasonic FL500 - DMW - Hot-shoe clip-on Flash User Manual preview
FL500 - DMW - Hot-shoe clip-on Flash
Brand: Panasonic Pages: 44
HAI Omni Pro II Quick Reference preview
Omni Pro II
Brand: HAI Pages: 2
La Crosse Technology 616-143 Quick Setup Manual preview
616-143
Brand: La Crosse Technology Pages: 2
VADDIO ZOOMSHOT 20 User Manual preview
ZOOMSHOT 20
Brand: VADDIO Pages: 20
VADDIO WallVIEW CCU HD-18 HD-SDI Installation And User Manual preview
WallVIEW CCU HD-18 HD-SDI
Brand: VADDIO Pages: 18
VADDIO RoboSHOT 12 User Manual preview
RoboSHOT 12
Brand: VADDIO Pages: 60
VADDIO ClearSHOT 10 USB Integrator'S Complete Manual preview
ClearSHOT 10 USB
Brand: VADDIO Pages: 62
VADDIO RoboSHOT 12 Installation And User Manual preview
RoboSHOT 12
Brand: VADDIO Pages: 41
Vacron VVH-MDE304 Quick Start Manual preview
VVH-MDE304
Brand: Vacron Pages: 2
VADDIO CLEARVIEW HD-18 Manual preview
CLEARVIEW HD-18
Brand: VADDIO Pages: 4

Brands by name

Popular brands

Load more brands