ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 33

Page: 33 / 200

1P+6

360° rectangular panoramic six
independent sub-screens.

●

You can zoom or drag the image on all
the screens.

●

You can move the start point (left and
right) on a rectangular panoramic image
screen.

1P+8

Original image eight
independent sub-screens.

●

You can zoom or drag the image on all
the screens.

●

You can rotate the image on the
original image screen to change the
start point.

Parameter

Description

Wall mount

180° rectangular panoramic image screen
(from left to right).
You can drag the image on all the screens
(up and down) to adjust the vertical view.

1P+3

180° rectangular panoramic image screen
+ three independent sub-screens.

●

You can zoom or drag the image on all
the screens.

●

You can drag the image on all the
screens (upper and lower) to adjust
the vertical view.

1P+4

180° rectangular panoramic image
four independent sub-screens.

●

You can zoom or drag the image on all
the screens.

●

You can drag the image on all the
screens (upper and lower) to adjust
the vertical view.

1P+8

180° rectangular panoramic image screen
+ eight independent sub-screens.

●

You can zoom or drag the image on all
the screens.

●

You can drag the image on all the
screens (upper and lower) to adjust
the vertical view.

Panorama

Drag or cross the screen 360° to unfold
the distortion panorama, and you can
drag the image in the left/right
direction.

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands

ICRealtime Edge IPEG-D20F-IRW3, User Manual

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands