ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 66

Page: 66 / 200

Auto

The system adjusts image clarity according to the environmental
conditions.

Off

Defog function is disabled.

Step 3

Click

Save

4.5.1.1.10

Fisheye

This function allows you to dewarp the 360 fisheye cameras to different layouts.

This function is only available on fisheye device.
Step 1

Select

Setting

Camera

Conditions

Fisheye

Figure 4-42 Fisheye

Step 2

Set install mode and record mode.

Table 4-16 Description of fisheye parameters

Parameter

Description

Install Mode

Select

Ceiling

Wall

, or

Ground

depending on the install evnironment

Record Mode

●

1O: The original image before correction.

●

1P: 360°rectangular panoramic image.

●

2P: Only available if the install mode is

Ceiling

Ground

Two associated 180° rectangular image screens, and at any
time, the two screens form a 360° panoramic image.

●

1R: Original image independent sub-screen.
You can zoom or drag the image in all the screens.

●

2R: Original image two independent
sub-screens. You can zoom or drag the image in all the
screens.

●

4R: Original image four independent
sub-screens. You can zoom or drag the image in all the
screens.

●

1O + 3R: Original image three independent
sub-screens. You can zoom or drag the image in original
image screen, and move the image (upper and lower) in
sub-screens to adjust the vertical view.

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands

ICRealtime Edge IPEG-D20F-IRW3, User Manual

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands