ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 130

Page: 130 / 200

you cannot select the

Device All Ports

checkbox.

●

Device start server port and Device end server port: Set Device

start
server port and device end server port, and the range is
1–65535.

Device End Server
Port

Step 4

Click

, and the

Firewall

interface is displayed.

Step 5

Click

Save

4.8.5 Peripheral

4.8.5.1

Serial Port Settings

This section configures the serial port if using an IPC PTZ with RS485 serial cable to another
device for control.
Step 1

Select

Setting

System

Peripheral

Serial Port Setting

Figure 4-121 Serial port settings

Step 2

Configure serial port settings parameters.

Table 4-43 Description of serial port settings parameters

Parameter

Description

Address

The corresponding device address. 1 by default.

Baud Rate

Select the baud rate for the camera. 9600 by default.

Date Bit

8 by default.

Stop Bit

1 by default.

Parity

None

by default.

Step 3

Click

Save

4.8.5.2

External Light

118

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

ICRealtime Edge IPEG-D20F-IRW3, User Manual, Page: 130 / 200

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews: