ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 103

Page: 103 / 200

●

If P2P is enabled and the status is Online, remote management on the device is supported.

●

When P2P is enabled and the status is Offline, make sure the IPC is connected to a
network and set it on DHCP.

Step 2

Device management

Step 3

Tap the

at the upper right corner.

Step 4

Scan the QR code on the

P2P

interface.

Step 5

Follow the instructions to finish the settings.

4.6.13.2

ONVIF

The ONVIF authentication is

by default, which allows the network video products (including

NVRs and other recording devices) from other manufacturers to connect to your device.

ONVIF is enabled by default.
Step 1

Select

Setting

Network

Port

ONVIF

Figure 4-88 ONVIF

Step 2

Select

Authentication

Step 3

Click

Save

4.6.13.3

RTMP

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands

ICRealtime Edge IPEG-D20F-IRW3, User Manual

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands