manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 9 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 9

4

1

PANEL DESCRIPTION

u

EXTERNAL DTMF CONTROL INDICATOR 

(p. 63)

Appears when the optional external DTMF control function
is in use.

• Available for the U.S.A. version only.

i

TOT (TIME-OUT TIMER) INDICATOR 

(p. 72)

Appears while the time-out timer has been activated.

o

AUDIO MUTE INDICATORS 

(p. 21)

Appear when the audio mute function is activated via mi-
crophone control.

• This function is cancelled when any switch or control is oper-

ated.

!0

PRIORITY WATCH INDICATORS 

(p. 48)

Appear while the priority watch is activated; flash while the
watch is paused.

!1

OUTPUT POWER INDICATORS 

(p. 25)

➥

“LOW” appears for low output power. (5 W)

➥

“LOW 

★

” appears for mid output power. (10 W)

➥

No indicator appears for high output power.

!2

MEMORY CHANNEL READOUTS

➥

Show the selected memory channel numbers. (p. 32)

➥

Only 2 capital “L”’s appear while the frequency lock
function is in use. (p. 16)

➥

A capital “C” appears while on a call channel (p. 37)

➥

“L1–L3” appear when a scratch pad memory is se-
lected. (p. 39)

➥

A small “c” appears when VFO mode is selected from
the call channel or a scratch pad memory (pgs. 37, 39)

!3

SKIP INDICATORS 

(p. 45)

Appear when the displayed memory channel is specified
as a skip channel.

!4

MEMORY INDICATORS 

(p. 32)

Appear when memory mode is selected.

!5

S/RF INDICATORS 

(p. 25)

➥

Show the relative signal strength while receiving sig-
nals.

➥

Show the output power selection while transmitting. 

!6

BUSY INDICATORS 

(p. 20)

Appear while a signal is being received or the squelch is
open.

!7

AUTO POWER-OFF INDICATOR 

(p. 73)

Appears while the auto power-off function is in use.

IC-2710H.qxd  02.2.8 16:55  Page 4 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments