manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 62 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 62

13

PAGER AND CODE SQUELCH

57

■

Code channels

D

Before programming

The pager and code squelch functions require ID codes and a
group code. These codes are 3-digit DTMF codes and must
be written in the code channels before operation. The trans-
ceiver has separate code channels for each band.

D

Code channel assignment

* Code channel P automatically memorizes an ID code when receiv-

ing a pager call. The contents in channel P cannot be changed
manually.

ID OR

GROUP CODE

CODE CHANNEL

NUMBER

“RECEIVE ACCEPT”

OR “RECEIVE INHIBIT”

Your ID code

0

“Receive accept” only.

Other parties’

ID code

1–5

“Receive inhibit” should

be programmed in each

channel.

Group code

One of 1–5

“Receive accept” must be

programmed.

Memory space*

P

“Receive inhibit” only.

RECEIVE ACCEPT AND INHIBIT

Code channels 1–5 can store the transmit codes for per-
sonal calls to other individuals and the group codes for
group calls.

The group codes should be programmed as “receive ac-
cept” (“

” disappears) to receive all calls from group

members.

If transmit codes are not programmed as “receive inhibit,”
the transceiver accepts calls directed to other individuals
and your answer back may confuse other members in your
group—this is not a selective calling system. Therefore,
transmit codes should be programmed as “receive inhibit”
(“

” appears) so the transceiver rejects calls directed to

other individuals.

SKIP

SKIP

IC-2710H.qxd  02.2.8 16:55  Page 57 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments