manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 82 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 82

18

MAINTENANCE

77

■

Fuse replacement

If the fuse blows or the transceiver stops functioning, find the
source of the problem if possible, and replace the damaged
fuse with a new, rated one (FGB 20 A) as shown in the dia-
gram below.

■

Partial resetting

If you want to initialize the operating conditions without clear-
ing the memory contents, etc., a partial reset function is avail-
able for the transceiver. The partial reset can be performed
independently for each band.

While pushing either left or right, or both [V/MHz] switches,
turn power ON to partially reset the transceiver.

➧

Initialized settings:

VFO frequency, SET mode settings.

➧

Retained settings:

Memory channels, call channels, offset
freq. in memory/call, DTMF memory,
pager and code squelch settings, initial
SET mode settings.

■

Resetting the transceiver

The function display may occasionally display erroneous in-
formation, (e.g. when first applying power). This may be
caused externally by static electricity or other factors.

If this problem occurs, turn power OFF. After waiting a few
seconds, turn power ON again. If the problem persists, per-
form the following procedure.

Partial resetting is alternatively available. See previous sec-
tion for details.

➀

Push [POWER] to turn power OFF.

➁

While pushing both left and right [S.MW] switches, turn
power ON.

• All LCD segments appear momentarily, the initial display appears

and the transceiver is reset.

CAUTION:

Resetting the transceiver 

CLEARS

all

memory information, and initializes all values in the trans-
ceiver.

IC-2710H.qxd  02.2.8 16:55  Page 77 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments