manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 81 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 81

18

MAINTENANCE

76

PROBLEM

POSSIBLE CAUSE

SOLUTION

REF.

Frequency cannot be set via
microphone.

• The frequency lock function is activated.

• The microphone keypad lock function is acti-

vated.

• Priority watch is paused on the watching fre-

quency.

• Push and hold [

(VFO)

LOCK] to deactivate the

frequency lock function.

• Push [FUNC], then [

A

16KEY LOCK] to deacti-

vate the microphone keypad lock function.

• Push the selected band’s [

(M/CALL)

PRIO] to re-

sume the watch.

p. 16

p. 16
p. 48

Some memory channels
cannot be selected via the
microphone keypad.

• The input channel number has not yet been pro-

grammed.

• Rotate the tuning dial to check whether the

channel has been programmed or not.

p. 32

Scan does not operate.

• Squelch is open.
• The selected scan edge memory channels (e.g.

1 A and 1b) have the same frequencies (for pro-
grammed scan).

• Only 1 memory channel is programmed or other

channels are set as skip channels.

• Priority watch is activated.

• Set the squelch to the threshold point.
• Reset the scan edges.

• Program other memory channels or cancel the

memory skip function in the desired channels.

• Turn the function OFF.

p. 20
p. 43

pgs.
33, 45
p. 48

Transmission is automati-
cally cut off.

• Time-out timer is activated.

• Set the timer to OFF.

p. 72

Transmission continues
even when the PTT is re-
leased.

• One-touch PTT function is activated.

• Turn the function OFF.

p. 26

The function display shows
erroneous information.

• The CPU is malfunctioning.

• Reset the transceiver.

p. 77

IC-2710H.qxd  02.2.8 16:55  Page 76 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments