manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 84 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 84

OPTIONS

20

79

Some of the following options may not be available due to
variations in local electrical standards, etc. If you have any
questions regarding options please consult your Icom Dealer.

D

Antenna

AH-32

144/430(440) MHz DUAL BAND ANTENNA

Dual band mobile antenna.
Frequency range: 144–148 MHz and 430–450 MHz.
Max. input power: 150 W

AHB-32

TRUNK MOUNT

Trunk mount with a coaxial cable for the AH-32.

D

Speakers

SP-7 

EXTERNAL SPEAKER

For base station use. Cable length: 1.0 m; 3.3 ft

SP-10 

EXTERNAL SPEAKER

Compact design. Cable length: 1.5 m; 4.9 ft

SP-12 

EXTERNAL SPEAKER

Slim-type. Cable length: 2.0 m; 6.6 ft

D

Separation accessories

OPC-600/601 

SEPARATION CABLE

For operation with the front panel detached.
Cable length
OPC-600: 3.5 m; 11.5 ft

OPC-601: 7.0 m; 23.0 ft

MB-58

REMOTE CONTROLLER BRACKET

Mounts the remote controller in a convenient location for op-
eration with the front panel detached from the main body.

MB-65

REMOTE CONTROLLER BRACKET

Mounts the remote controller with MB-58. Adjustable angle
and direction for optimum installation positioning.

OPC-440/647

MIC EXTENSION CABLE

Cable length
OPC-440: 5.0 m; 16.4 ft

OPC-647: 2.5 m; 8.2 ft.

OPC-347

DC POWER CABLE

Has a 20 A capacity and a length of 7.0 m (23.0 ft).

OPC-441

SPEAKER EXTENSION CABLE

Cable length: 5.0 m; 16.4 ft.

SP-7

SP-10

SP-12

MB-65

IC-2710H.qxd  02.2.8 16:55  Page 79 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments