manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 12 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 12

1

PANEL DESCRIPTION

7

■

Microphone keypad

FUNCTION

SECONDARY FUNCTION (after 

)

FUNC

OTHER FUNCTIONS

Toggles between opening and closing the
accessed band’s squelch.

(p. 20)

No secondary function.

After :

Transmit the appropriate
DTMF code or push [1] to
[8] to transmit the DTMF
memory contents when
the DTMF memory en-
coder is activated. (p. 51)

DTMF-S

• Starts and stops scanning.

(p. 42)

• Starts tone scan when an optional tone

squelch is in use.

(p. 55)

No secondary function.

Starts and stops priority watch.

(p. 48)

Turns the one-touch PTT function ON and
OFF.

(p. 26)

Selects high output power.

(p. 26) Turns the optional pager function ON.(p. 59)

Selects middle output power.

(p. 26) Turns the optional code squelch function

ON.

(p. 62)

Selects low output power.

(p. 26) Turns the DTMF memory encoder function

ON.

(p. 50)

Selects –duplex.

(p. 28) Turns the subaudible tone encoder ON.

(p. 28)

Sduplex.

(p. 28) Turns the optional pocket beep function ON.

(p. 53)

Selects simplex

(p. 28) Turns the optional tone squelch function

ON.

(p. 54)

Increases the audio output.

(p. 20)

While being pushed,  transmits a 1750 Hz
tone.

(p. 28)

AFC

1

MONI

AFC-OFF

2

SCAN

PTT-M

3

PRIO

PGR

4

HIGH

CSQL

5

MID

DTMF

6

LOW

TONE

7

DUP–

TSQL

S

8

DUP+

TSQL

9

SIMP

TONE-2

0

VOL

KEY

IC-2710H.qxd  02.2.8 16:55  Page 7 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments