manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 16 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 16

2

INSTALLATION

11

■

Microphone connection

The microphone connector is located behind the front panel.
Connect the supplied microphone as follows:

➀

Push the release button, then detach the remote controller
as shown below.

➁

Connect the supplied microphone to the microphone con-
nector.

➂

Reattach the remote controller to the main body.

➃

To remove the microphone, push the release button as
above.

■

Separate installation

Using an optional OPC-600/601 

SEPARATION CABLE

, the front

panel can be separated from the main body, doubling as a re-
mote controller.

➀

Detach the front panel as shown at left.

➁

Connect a separation cable to the front panel and to the
main body using the supplied screws as illustrated below.

mic release

Push 

Release
button

OPC-600 or OPC-601

Rear of front panel

Main body

➀

8 V OUT

➁

Freq. up/down

➂

8 V control IN

➃

PTT

➄

Mic AF (–)

➅

Mic AF (+)

➆

Ground

➇

Data IN

➇

➀

Microphone pin assignments

IC-2710H.qxd  02.2.8 16:55  Page 11 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments