Icom IC-2710H Instruction Manual Download Page 33

Page: 33 / 88

REPEATER OPERATION

Push [BAND] to select the desired band, if nec-
essary.

Set the receive frequency (repeater output fre-
quency). (pgs. 15–19)

Push [

➆

DUP–] to select – duplex; push

[

➇

DUP+] for + duplex.

Push [FUNC] then [

➆

TONE] to turn ON the sub-

audible tone encoder according to repeater re-
quirements.

• Refer to p. 29 for tone frequency setting.

• When the repeater requires a different tone system,

see at right.

Push and hold [PTT] to transmit.

Push and hold [

➀

MONI] to check whether the

other station’s signal can be directly received.

Release [PTT] to receive.

To return to simplex operation, push [

➈

SIMP].

To turn OFF the subaudible tone encoder, push
[FUNC], then [

T-OFF].

DTMF tones

Push [DTMF-S], then push the keys of the desired
DTMF digits.

• The function indicator lights green.
• 0–9, A–D,

(E) and #(F) are available.

• Cancel the DTMF memory encoder or optional pager/code

squelch function in advance. (pgs. 49, 59, 62)

• Push [DTMF-S] again to return the keypad to normal

function control.

• The transceiver has 8 DTMF memory channels for au-

topatch operation. See p. 49 for details.

1750 Hz tone

A 1750 Hz tone is required to access most
European repeaters. The microphone has 1750
Hz tone capability.

Push [FUNC].

• The mode indicator lights orange.

Push [

TONE-1] to transmit a 1750 Hz tone call signal for

1 sec.; push and hold [

TONE-2] to transmit a 1750 Hz

tone call signal for an arbitrary period.

• The mode indicator goes out automatically.
• The optional HM-90 also has 1750 Hz tone capability.

DTMF S

TONE-1

TONE-2

DUP–

DUP+

SIMP

IC-2710H.qxd 02.2.8 16:55 Page 28 (1,1)

Summary of Contents for IC-2710H

























































































Search results

Summary of Contents for IC-2710H

Reviews:

Icom IC-2710H, Instruction Manual, Page: 33 / 88

Search results

Summary of Contents for IC-2710H

Reviews: