Icom IC-2710H Instruction Manual Download Page 10

Page: 10 / 88

PANEL DESCRIPTION

■

Rear panel

w
e

ANTENNA CONNECTOR [ANT]

Accepts a 50

Ω

dual band antenna with a PL-259 connec-

tor. (p. 14)

SPEAKER JACK 1 [144 MHz SP]

Connects a 4–8

Ω

speaker, if required. Outputs the 144

MHz band’s audio. See the table at right for details.

SPEAKER JACK 2 [430(440) MHz SP]

Connects a 4–8

Ω

speaker, if required. Outputs both

band’s audio when [430(440) MHz SP] has no connection.

POWER RECEPTACLE [DC13.8V]

Accepts 13.8 V DC with the supplied DC power cable.

Speaker information

Connected
speaker

VHF band audio

UHF band audio

With no exter-
nal speakers

Internal speaker (mixed audio)

[144 MHz SP]
only

External speaker

[430(440) MHz
SP] only

External speaker (mixed audio)

2 external
speakers

External speaker via
[144 MHz SP]

External speaker via
[430(440) MHz SP]

Internal speaker

IC-2710H.qxd 02.2.8 16:55 Page 5 (1,1)

Summary of Contents for IC-2710H

























































































Search results

Summary of Contents for IC-2710H

Reviews:

Icom IC-2710H, Instruction Manual, Page: 10 / 88

Search results

Summary of Contents for IC-2710H

Reviews: