manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 76 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 76

16

WIRELESS OPERATION

71

■

Microphone
address

The transceiver has 8 possible microphone addresses to help
prevent interference from other HM-90 

WIRELESS MICRO

-

PHONES

. Set both the microphone address and microphone

dip switch to the same value as follows.

NOTE:

When the supplied microphone is connected, the

transceiver rejects control signals from the HM-90 even
when the microphone address is matched.

D

Microphone address

➀

Push [POWER] to turn power
OFF.

➁

While pushing [

(VOL)

SET L],

turn power ON to enter initial
set mode.

➂

Push [SET] a few times to se-
lect the “Adr” display as
shown at right.

➃

Rotate the left-hand tuning dial to set the microphone ad-
dress to 0–7 or to turn the microphone control OFF.

• When “Adr-oF” is selected, the transceiver rejects all control sig-

nals from the HM-90.

➄

Turn power OFF to exit initial set mode.

USING

INITIAL SET MODE

The display shows the mi-
crophone address is set to 1.

D

Microphone dip switch

➀

Remove the switch cover from the microphone rear panel.

➁

Set the microphone dip switch and the microphone ad-
dress to the same value as shown below.

➂

Replace the switch cover.

MICROPHONE

ADDRESS

DIP SWITCH

S1–1

S1–2

S1–3

Adr-0

OFF

OFF

OFF

Adr-1 (default)

ON

OFF

OFF

Adr-2

OFF

ON

OFF

Adr-3

ON

ON

OFF

Adr-4

OFF

OFF

ON

Adr-5

ON

OFF

ON

Adr-6

OFF

ON

ON

Adr-7

ON

ON

ON

LOCK

AFC

AFC-OFF

PTT-M

MW

PGR

CALL

1

2

3

A

4

5

6

B

MR

VFO

CLR

C-SQL

DTMF

D-OFF

HIGH

MID

LOW

SET

Dip switch

ON

OFF

1  2  3

(S1)

Switch cover

IC-2710H.qxd  02.2.8 16:55  Page 71 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments