Icom IC-2710H Instruction Manual Download Page 71

Page: 71 / 88

WIRELESS OPERATION

■

Connection

Wireless remote control is available when the following op-
tions are used:
• HM-90

WIRELESS MICROPHONE

• EX-1759

INFRARED RECEIVER

The BC-96

MICROPHONE HOLDER

is additionally recommended

for use with the HM-90, since the HM-90’s internal battery re-
quires charging.

Recommended connection

■

HM-90

WIRELESS MICROPHONE

The HM-90’s internal battery should be charged when the mi-
crophone is not being held.

Charging period: 1.5 hrs. with timer

(or 8 hrs. when battery is exhausted)

Operating period: 12 hrs (Operation : standby= 1 : 4)

Charging method

Choose a method from one of the following:

• Connect the cable from the HM-90 to the EX-1759.
• Connect the BC-96 and EX-1759; then put the HM-90 into

the BC-96 (refer to the diagram at left).

• Use the CP-1

CIGARETTE LIGHTER CABLE

to connect the

BC-96 and cigarette lighter socket.

Turning the wireless remote ON/OFF

When you use the HM-90 as a wired microphone, turn OFF
the wireless remote control circuit if desired.

LOCK

AFC

AFC-OFF

PTT-M

PGR

CALL

VFO

CLR

C-SQL

DTMF

D-OFF

HIGH

MID

LOW

SET

The diagram shows that
the wireless remote con-
trol function is turned
ON.

Dip switch

1 2 3 4

OFF

optional EX-1759 and HM-90

IC-2710H

EX-1759

BC-96

Use the
microphone’s
cable

HM-90

IC-2710H.qxd 02.2.8 16:55 Page 66 (1,1)

Summary of Contents for IC-2710H

























































































Search results

Summary of Contents for IC-2710H

Reviews:

Icom IC-2710H, Instruction Manual, Page: 71 / 88

Search results

Summary of Contents for IC-2710H

Reviews: