manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 38 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 38

6

MEMORY OPERATION

33

■

Programming a memory channel

VFO mode settings, including the set mode contents such as
subaudible tone frequency, etc., are programmed into a mem-
ory channel.

➀

Set the desired frequency in VFO mode:

➥

Push the desired band’s [V/MHz] to select VFO mode.

➥

Set the frequency using the desired band’s tuning dial.

➥

Set other data (e.g. tone frequency, etc.) if required.

➁

Push [S.MW] momentarily.

• “

!

” and the memory channel number flashes.

➂

Rotate the tuning dial to select the memory channel to be

programmed.

• Memory channels not yet programmed are blank.

➃

Push [S.MW] for 1 sec. to program.

• 3 beeps may sound.
• Memory channel number automatically advances when continu-

ing to push [S.MW] after programming.

✔

CONVENIENT

Memory programming can be performed in versatile ways
e.g. memory channel to the same (or different) memory chan-
nel, memory channel to the call channel, etc.

[EXAMPLE]:

Programming 145.870 MHz into memory channel 20 via the remote controller.

1

5

9

1

5

9

1

5

9

S.MW MW

Push

and

Rotate

for setting
freq., etc.

Rotate

Push

momentarily

S.MW MW

Push

for 1 sec. and continue pushing

V/MHz

SCAN

IC-2710H.qxd  02.2.8 16:55  Page 33 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments