manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 73 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 73

16

WIRELESS OPERATION

68

■

HM-90 switches

➊

PTT SWITCH

➥

Push and hold to transmit; release to receive.

➥

Toggles between transmitting and receiving while the
one-touch PTT function is in use.

➋

BAND SWITCHES [BAND SELECT 

Y

,

Z

]

➥

Select the desired band as the main band.

➥

Activate the para-watch function when pushed and held
when the main band is selected.

➥

Activate the sub band access function after pushing
[FUNC] on the rear panel.

➌

MONITOR SWITCH [MONI]

Toggles between opening and closing the accessed band’s
squelch.

BAND
SELECT

MONI

REMOTE CONTROL MICROPHONE

VOL

SQL     

LOCK

JAPAN

AFC

AFC-OFF

PTT-M

MW

PGR

CALL

1

2

3

A

4

5

6

B

M

0

#

D

MR

VFO

CLR

C-SQL

DTMF

D-OFF

SCAN

MONI

FUNC

DTMF

KEY

DTMF

MEMO

MUTE

SQL

ENT

7

8

9

C

DUP–

DUP+

SIMP

SPCH

PRIO

REAR LOCK

DEMO

TONE

HIGH

MID

LOW

SET

T-SQL

S

T-SQL

T-OFF

➓

➊

➋

➌

➍

➎

➏

➐

➑

➒

Front and side panels

Rear panel

➍

SQUELCH LEVEL UP/DOWN SWITCHES
[

Y

SQL], [

Z

SQL]

Vary the accessed band’s squelch threshold point for noise
mute.

➎

FREQUENCY UP/DOWN SWITCHES [UP], [DN]

➥

Push either switch to change the operating frequency,
memory channel, set mode contents, etc.

➥

Push and hold either switch to start scanning.

➏

ACTIVITY INDICATOR [UP], [DN]

Lights red while a key is pushed; lights green while the
one-touch PTT function is in use.

➐

AUDIO VOLUME UP/DOWN SWITCHES
[

Y

VOL], [

Z

VOL]

Adjust the accessed band’s audio level.

➑

MODE INDICATOR

Indicates the microphone condition.

• Lights red when [FUNC] is pushed.
• Lights green when [DTMF KEY] is pushed.
• Lights orange when [DTMF MEMO] is pushed.

➒

LOCK SWITCH [LOCK]

Locks all switches and keys on the microphone except for
the PTT switch.

➓

KEYPAD

Used for controlling the transceiver, transmitting a DTMF
memory channel, etc. 

IC-2710H.qxd  02.2.8 16:55  Page 68 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments