Icom IC-2710H Instruction Manual Download Page 20

Page: 20 / 88

SETTING A FREQUENCY

■

Preparation

Turning power ON

Push [POWER] for 1 sec. to turn power ON.

Main band

The IC-2710H can receive 144 MHz and 430(440) MHz band
signals simultaneously. Function access or frequency
changes affect the main band only. In addition, signals can
be transmitted on the main band only. Set the desired band
as the main band.

Push the desired band’s tuning dial to select the main band.

• “

” indicates the main band.

Push [BAND] to toggle the main band selection
between the 144 and 430(440) MHz bands.

VFO and memory modes

The transeiver has 2 normal operating modes: VFO mode
and memory mode. You can select VFO mode or memory
mode independently on each band.

Push the desired band’s [V/MHz] to select VFO mode when
the transceiver is not in VFO mode.

• If VFO mode is already selected, the digits below 100 kHz disap-

pear. In this case, push [V/MHz] again (or push twice depending on
version).

Push [VFO] to select VFO mode.

• The microphone controls the main band only (or using

sub band access; p. 22). Push [BAND] to toggle the
main band, then push [VFO], if necessary.

Push [POWER] for 1 sec.

BAND

Indicates memory mode

VFO mode is selected

VFO

IC-2710H.qxd 02.2.8 16:55 Page 15 (1,1)

Summary of Contents for IC-2710H

























































































Search results

Summary of Contents for IC-2710H

Reviews:

Icom IC-2710H, Instruction Manual, Page: 20 / 88

Search results

Summary of Contents for IC-2710H

Reviews: