manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 26 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 26

4

BASIC OPERATION

21

■

Avionics band receive

(U.S.A. version only)

AM mode can be selected over the range of 118.000 to
135.995 MHz for reception of avionics-related broadcasts.

➥

Push and hold [

(SQL)

MONI] to toggle between AM and FM

modes.

• Mode selection cannot be performed via the microphone.

NOTE:

The avionics band can be selected in the left band

only, even when the para watch fuinction is in use.

✔

CONVENIENT

The tuning steps for the avionics band are available sepa-
rately from those for other ranges.

1

5

9

Appears when AM
mode is selected.

■

Monitor function

This function is used to listen to weak signals without disturb-
ing the squelch setting or to open the desired band’s squelch
manually even when the optional mute functions such as tone
squelch, pager functions, etc., are in use.

Push the desired band’s [MONI] to open the desired band’s
squelch.

• Push [MONI] again to cancel the function.
• While duplex is ON for repeater operation, the transmitting fre-

quency can be monitored with [MONI].

Ä

Push [BAND] to change bands, if necessary.

Å

Push [

➀

MONI] to open the main band’s

squelch.

• Push [

➀

MONI] again to cancel the function.

■

Audio mute function

This function mutes both band’s audio signals
without disturbing the volume settings.

Ä

Push [FUNC] then [

H

MUTE] to mute both band’s audio signals.

• “MUTE” appears for both bands.

Å

Push [

E

CLR] (or any other key) to cancel the function.

• “MUTE” disappears.

MONI

➀

MUTE

H

IC-2710H.qxd  02.2.8 16:55  Page 21 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments