manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 2 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 2

R

WARNING! NEVER 

connect the transceiver to an

AC outlet. This may pose a fire hazard or result in an electric
shock.

R

WARNING! NEVER 

operate the transceiver while

driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.

NEVER

connect the transceiver to a power source of more

than 16 V DC. This connection will ruin the transceiver.

NEVER

connect the transceiver to a power source using

reverse polarity. This connection will ruin the transceiver.

NEVER

cut the DC power cable between the DC plug and

fuse holder. If an incorrect connection is made after cutting,
the transceiver might be damaged.

NEVER

place the transceiver where normal operation of

the vehicle may be hindered or where it could cause bodily
injury.

NEVER

let objects impede the operation of the cooling fan

on the rear panel.

DO NOT 

push the PTT when not actually desiring to transmit.

i

IMPORTANT

READ ALL INSTRUCTIONS 

carefully and completely before

using the transceiver.

SAVE THIS INSTRUCTION MANUAL—

This instruction man-

ual contains important operating instructions for the
IC-2710H.

EXPLICIT DEFINITIONS

The explicit definitions below apply to this instruction manual.

CAUTIONS

WORD

DEFINITION

R

WARNING

Personal injury, fire hazard or electric shock
may occur.

CAUTION

Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.

The IC-2710H Europe versions comply with essential re-
quirements of the 89/336/EEC directive for Electromagnetic
Compatibility. This compliance is based on conformity with
the ETSI specification prEIS300 684 (EMC product standard
for Commercially Available Amateur Radio Equipment).

IC-2710H.qxd  02.2.8 16:55  Page i (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments