manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 34 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 34

5

REPEATER OPERATION

29

■

Subaudible tones

➀

Push the desired band’s tuning dial.

➁

Select the mode/channel you wish to set the subaudible
tone frequency to, such as VFO mode or memory/call
channel.

➂

Push [SET] one or more times until “T” appears and
flashes as shown above.

• Push [MONI] to reverse the order of selection.
• Cancel the DTMF memory encoder or optional pager/code

squelch function in advance. (pgs. 49, 59, 62)

➃

Rotate the selected band’s tuning dial to select and set the
desired frequency.

➄

Push the desired band’s tuning dial to exit set mode.

NOTE:

The subaudible tone frequency can be set in a

memory channel temporarily. However, the set contents
are cleared once the memory/call mode is selected. To
store the tone frequency permanently, overwrite the chan-
nel information.

USING

SET MODE

1

5

9

T

Separate setting for each band

The display shows that an 
88.5 Hz subaudible tone fre-
quency is set.

Ä

Push [BAND] to select the desired band, if nec-
essary.

Å

Set the mode/channel you wish to set the sub-
audible tone frequency to, such as VFO mode,
memory/call channel or scratch pad memory.

• The subaudible tone frequency is independently pro-

grammed into each mode or channel.

Ç

Push [

F

SET] one or more times until “T” ap-

pears and flashes as shown at left.

• Pushing [

G

ENT] reverses the order of selection.

• Cancel the DTMF memory encoder or optional

pager/code squelch function in advance. (pgs. 49,
59, 62)

É

Push [

Y

] or [

Z

] to select and set the desired

frequency.

• Pushing and holding [

Y

] or [

Z

] changes the fre-

quency continuously.

Ñ

Push [

E

CLR] to exit set mode.

•

Subaudible tone frequency list

(unit: Hz)

SET

B

67.0

79.7

94.8

110.9

131.8

156.7

171.3

186.2

69.3

82.5

97.4

114.8

136.5

159.8

173.8

189.9

71.9

85.4

100.0

118.8

141.3

162.2

177.3

192.8

74.4

88.5

103.5

123.0

146.2

165.5

179.9

196.6

77.0

91.5

107.2

127.3

151.4

167.9

183.5

199.5

203.5
206.5
210.7
218.1
225.7

229.1
233.6
241.8
250.3
254.1

IC-2710H.qxd  02.2.8 16:55  Page 29 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments