manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 66 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 66

13

PAGER AND CODE SQUELCH

61

■

Code squelch function

The code squelch function can be used only when an optional
UT-49 is installed.

Code squelch operation provides communication with silent
standby since you only receive calls from stations which know
your ID or group code. To use the code squelch function in
your group, all stations need the code squelch function.

The code squelch function transmits a 3-digit code prior to
voice transmission in order to open the receiving station’s
code squelch.

PERSONAL CALLS

This display appears when
you are called with your ID
code and the calling station’s
ID code is 263.

GROUP CALLS

This display appears when
you are called with the group
code, 123, and 123 has been
programmed into code chan-
nel 5.

ERROR INFORMATION

When the transceiver receives
an incomplete signal, “E” ap-
pears.

SKIP

1

5

9

1

5

9

SKIP

1

5

9

“E” appears

CODE SQUELCH SIMULATION:

No code squelch
function

111

111/555

000/555

000

IC-2710H.qxd  02.2.8 16:55  Page 61 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments