manualshive.com logo in svg

Icom IC-2710H, Instruction Manual, Page: 39 / 88

Share
Download
Icom IC-2710H Instruction Manual Download Page 39

6

MEMORY OPERATION

34

■

Programming a memory channel via the microphone

Memory channel programming can be performed
via the microphone.

Ä

Push [BAND] to select the desired band, if necessary.

Å

Set the desired frequency in VFO mode:

➥

Push [VFO] to select VFO mode.

➥

Set the frequency using the keypad.

➥

Set other data (e.g. offset frequency, duplex direction, subaudi-
ble tone encoder ON/OFF and its frequency), if required.

MW

Ç

Push [FUNC] then [

E

MW] momentarily.

É

Select the memory channel to be programmed:

➥

Push [

Y

] or [

Z

] to select the memory channel (direct numeral

input cannot be used).

Ñ

Push [FUNC] then [

E

MW] for 1 sec. to program.

➥

3 beeps may sound and the VFO contents (including the sub-
audible tone frequency, etc.) are programmed.

➥

Memory channel number advances when continuing to push
[MW] after programming.

[EXAMPLE]:

Programming 145.870 MHz into memory channel 20 via the microphone.

1

5

9

1

5

9

1

5

9

Push

,

Push

then

momentarily

Push

Push

for 1 sec. and
              continue pushing

BAND

VFO

8

DUP+

7

DUP

5

MID

1

MONI

4

HIGH

C

ENT

MW

FUNC

A

CLR

then

MW

FUNC

A

CLR

IC-2710H.qxd  02.2.8 16:55  Page 34 (1,1)

Summary of Contents for IC-2710H

























































































Reviews:

No comments