IBM 4232 Model 302 Manual Download

Page: 84 / 274

Using the Printer Verification Test for the F2 Forms
Device

To run the printer verification test, follow these steps:

1. Turn the power On (|) if not already on.

2. Wait until the printer displays

3. Press Stop.

The printer displays

and then may display

Ignore this message until you have attached the printer to your
computer. (Press Stop to turn off the alarm, if necessary.)

4. Press Test.

The printer displays

READY

<A>

NOT READY

<A>

ð29 LINK ERROR

OPERATOR PRINT TESTS
Printer Demonstration

1-62

User’s Guide Model 302

Summary of Contents for 4232 Model 302



















































































































































































































































































Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands

IBM 4232 Model 302, Manual

Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands