IBM 4232 Model 302 Manual Download | Manualshive

Page: 11 / 274

background image

Notices

References in this publication to IBM products, programs, or services
do not imply that IBM intends to make these available in all countries
in which IBM operates. Any reference to an IBM product, program,
or service is not intended to state or imply that only IBM's product,
program, or service may be used. Any functionally equivalent
product, program, or service that does not infringe any of the
intellectual property rights of IBM may be used instead of the IBM
product, program, or service. The evaluation and verification of
operation in conjunction with other products, except those expressly
designated by IBM, are the responsibility of the user.

IBM may have patents or pending patent applications covering
subject matter in this document. The furnishing of this document
does not give you any license to these patents. You can send

|

license inquiries, in writing, to the IBM Director of Licensing, IBM

|

Corporation, 500 Columbus Avenue, Thornwood, NY 10594 USA.

Electronic Emission Notices

Federal Communication Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his own
expense.

|

Properly shielded and grounded cables and connectors (IBM part

|

number 04H5053 or its equivalent) must be used in order to meet

|

FCC emission limits. IBM is not responsible for any radio or
television interference caused by using other than recommended



Copyright IBM Corp. 1993, 1994

ix

«
...
9
10
11
12
13
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

Brand: IBM Pages: 112

Brand: D-Link Pages: 12

Brand: DataCard Pages: 78

Brand: DataCard Pages: 8

Brand: DataCard Pages: 136

Brand: DataCard Pages: 22

Brand: DataCard Pages: 16

Brand: DataCard Pages: 216

Brand: DataCard Pages: 19

Brand: DataCard Pages: 2

Brand: DataCard Pages: 30

Brand: DataCard Pages: 2

Brand: DataCard Pages: 4

Brand: DataCard Pages: 24

Brand: DataCard Pages: 134

Brand: DataCard Pages: 13

ImageCard series

Brand: DataCard Pages: 2

ImageCard series

Brand: DataCard Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands