IBM 4232 Model 302 Page 36 Manual Download

Page: 36 / 274

4) Try another electrical device (such as a lamp) in the

outlet.

5) If the outlet is working, connect the printer to the outlet

again. Return to Step 4 on page 1-12 and try again.

6) If the printer still fails to come on, call your service

representative.

b. Did the printer display a code or message and did the same

code or message remain on the display after approximately
30 seconds?

Yes, go to Appendix B, “Problem Solving,” find the

status code or message the printer displayed, and follow
the instructions.

No, go to Step 5c.

c. Did the indicators or display not respond, or did you have an

alarm problem?

Yes, then call for service.

No, go to Step 6.

6. The shipping box for the forms device has printing on the side to

help you identify what type of forms device you have. Note
which forms device is checked off, then remove the forms device
from the shipping box.

Note: If you have forms device F3, the shipping box also
contains the lower forms guides and F3 paper door.

7. Press Menu.

The printer displays

8. Press Scroll

↑

or Scroll

↓

until the printer displays

CONFIGURATION MENU
Print Format and Quality

CONFIGURATION MENU
Printer Setup

1-14

User’s Guide Model 302

Summary of Contents for 4232 Model 302



















































































































































































































































































Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands

IBM 4232 Model 302, Manual

Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands