IBM 4232 Model 302 Page 98 Manual Download | Manualshive

Page: 98 / 274

background image

Adjusting the Tear-off Position
The Dual Purpose Forms Device Document on Demand features
allow you to tear off a form using the tear bar upon completing a
print job. You can then prepare the printer to print the next print job.

Te a r B a r

To change the tear-off position of a form, follow these steps:

|

1. Make sure the printer is at the top of form position. Press

|

Load/Eject one time.

The printer displays

and the Ready indicator goes off. The paper quickly advances

|

to the tear-off position. You can also use the Automatic Eject or

|

Automatic Restore options to change the tear-off position of a

|

form. See

IBM 4232 Printer Model 302 Operator Panel

|

Instructions for more information on these options.

2. Open the acoustic cover.

3. If the perforation on the form is not at the tear-off position, use

the Micro

↑

, Micro

↓

, and Line Feed keys to adjust the form

position until the perforation is exactly in line with the tear-off bar.
The limits for the Tear-off Position Adjustment from the default
position is

±

19.05 mm (0.75 in.).

ðð3 FORMS EJECTED

PRESS LOAD

1-76

User’s Guide Model 302

«
...
96
97
98
99
100
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

Brand: Canon Pages: 29

PIXMA MX410 Series

Brand: Canon Pages: 46

Brand: Canon Pages: 65

Brand: Canon Pages: 4

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Sure shot 80 tele

Brand: Canon Pages: 39

BJC6500 - BJC 6500 Color Inkjet Printer

Brand: Canon Pages: 6

Brand: Canon Pages: 20

imagePROGRAF iPF6450

Brand: Canon Pages: 35

PIXMA MX340 Series

Brand: Canon Pages: 11

PIXMA MX340 Series

Brand: Canon Pages: 16

imagePROGRAF iPF6300S

Brand: Canon Pages: 12

Brand: Canon Pages: 19

Brand: Canon Pages: 101

iP4700 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 28

Brand: Canon Pages: 2

Brand: Canon Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands