IBM 4232 Model 302 Page 28 Manual Download

Page: 28 / 274

Installing the Ribbon Cartridge and Guide

The following sections describe preparation, installation, and
verification of the ribbon cartridge.

To install a new ribbon cartridge, follow these steps:

1. Slide the print head to the center of the printer.

2. Remove the ribbon cartridge from the package.

3. Remove the yellow clip from the ribbon.

4. Turn the blue ribbon advance knob clockwise to take up slack

in the ribbon. If the ribbon does not move, contact your place of
purchase and replace the ribbon cartridge.

Remove Yellow Clip

Blue Ribbon Advance Knob

1-6

User’s Guide Model 302

Summary of Contents for 4232 Model 302



















































































































































































































































































Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands

IBM 4232 Model 302, Manual

Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands