manualshive.com logo in svg

IBM 4232 Model 302, Manual

Share
Download
IBM 4232 Model 302 Manual Download Page 212

 

 
 

  1. Press Stop.

2. Be sure that the print head movement is not blocked.
3. Press Start to resume printing.
4. If the printer displays any of these status codes again:

a. Turn the power Off (O).
b. Wait 10 seconds, then turn the power On (|).

c. Run the Printer Verification Test (see “Printer Verification” on

page  4-12).

d. If the printer displays this status code again, call for service.

ð5ð MACHINE CHECK

SEE USER'S GUIDE

ð51 MACHINE CHECK

SEE USER'S GUIDE

ð52 MACHINE CHECK

SEE USER'S GUIDE

ð53 MACHINE CHECK

SEE USER'S GUIDE

ð55 MACHINE CHECK

SEE USER'S GUIDE

ð56 MACHINE CHECK

SEE USER'S GUIDE

ð58 PRINTER BOARD FAILURE

SEE USER'S GUIDE

B-12

User’s Guide Model 302 

 

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands