IBM 4232 Model 302 Manual Download

Page: 156 / 274

Operating States

Online – The printer is

online when the Online indicator is on, power

is On (|), the power-on tests complete, and the printer is able to
communicate with the computer.

Offline – The printer is

offline when the Online indicator is Off, the

power-on tests are running, or the printer is in test mode (Operator
Print Tests).

Ready and Not Ready

Ready – The printer is

ready when you press Start and there are no

error conditions. The printer can be

ready and online or offline.

Ready is indicated when the Ready indicator is On. See “Ready
Indicator” on page 2-11 for more information.

The printer displays

unless an information message overrides

ready or the printer is

offline.

Not Ready – The printer is

not ready when you press Stop or when

an error or operator intervention condition occurs. The printer can be
not ready and online or offline.

The printer displays

or a status code and message, and the Ready indicator is Off. See
“Ready Indicator” on page 2-11 for more information.

READY

<A>

NOT READY

<A>

2-14

User’s Guide Model 302

Summary of Contents for 4232 Model 302



















































































































































































































































































Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands

IBM 4232 Model 302, Manual

Search results

Summary of Contents for 4232 Model 302

Reviews:

Related manuals for 4232 Model 302

Brands by name

Popular brands